Tutorials

Build a line-follower robot from scratch

CircuitBay Team · · Updated · 12 min read

A line-follower robot drives along a black line on a white surface on its own. It is the classic first robot and the entry event at most college tech fests, because it teaches the three things every robot needs: sensing, deciding and moving. This guide builds a two-sensor version you can later upgrade to five sensors and PID control.

Parts

  • 2WD robot chassis with two geared DC motors and a caster wheel
  • L298N dual motor driver
  • Two IR sensor modules (or a 5-channel IR array)
  • Arduino Uno or Nano
  • Battery holder with 2 × 18650 cells (about 7.4 V)
  • Jumper wires

How it works

Mount the two IR sensors at the front, just either side of the line. On white, both sensors see a reflection; over the black line, the reflection drops. If the left sensor sees the line, the robot has drifted right, so it turns left — and vice versa. Most IR modules output LOW over a black line; if yours does the opposite, flip the comparison in the code.

Wiring

  • L298N OUT1/OUT2 → left motor, OUT3/OUT4 → right motor
  • L298N ENA, IN1, IN2 → Arduino pins 5, 7, 8; ENB, IN3, IN4 → pins 6, 9, 10 (remove the ENA/ENB jumpers)
  • Battery + → L298N 12V input, battery − → L298N GND and Arduino GND (common ground)
  • Left IR OUT → pin 2, right IR OUT → pin 3, sensor VCC/GND → 5V/GND

The code

const int L_SENSOR = 2, R_SENSOR = 3;
const int ENA = 5, IN1 = 7, IN2 = 8, ENB = 6, IN3 = 9, IN4 = 10;
const int SPEED = 150; // 0-255: start slow, raise once it tracks well

void drive(int left, int right) {
  digitalWrite(IN1, left > 0);  digitalWrite(IN2, left < 0);
  digitalWrite(IN3, right > 0); digitalWrite(IN4, right < 0);
  analogWrite(ENA, abs(left));  analogWrite(ENB, abs(right));
}

void setup() {
  const int outputs[] = {ENA, IN1, IN2, ENB, IN3, IN4};
  for (int pin : outputs) pinMode(pin, OUTPUT);
  pinMode(L_SENSOR, INPUT);
  pinMode(R_SENSOR, INPUT);
}

void loop() {
  bool leftOnLine = digitalRead(L_SENSOR) == LOW;
  bool rightOnLine = digitalRead(R_SENSOR) == LOW;

  if (leftOnLine && !rightOnLine) drive(0, SPEED);       // drifted right: turn left
  else if (rightOnLine && !leftOnLine) drive(SPEED, 0);  // drifted left: turn right
  else drive(SPEED, SPEED);                              // centred: go straight
}

Tuning tips

  • Set each IR module's potentiometer so its LED switches cleanly between the line and the white surface.
  • If the robot overshoots curves, lower SPEED or move the sensors closer together.
  • If one motor runs backwards, swap its two wires on the L298N.
  • A 25 mm wide black electrical-tape line on white chart paper makes a good practice track.

Upgrade: five sensors and PID

Competition robots use a five-sensor array to estimate how far the robot is from the centre of the line, then a PID controller to steer smoothly instead of zig-zagging. Once the two-sensor version works, swapping in an array and adding PID is the natural next step.

Questions or improvements? Join the discussion →

Built this? Share it with the bay.

Submit your project →

FROM THE COMMUNITY

Related projects

Robotics

Hallway Delivery Bot

A line-following rover that carries notes between classrooms.

  • Arduino
  • IR array
  • L298N